We Broke Our 4WD Power Wheels Go Kart on the FIRST JUMP! Road Test, Fuel Tank, Floor Mounted!

  Үзсэн тоо 158,653

CarsandCameras

2 сарын өмнө

We change the final drive gear on our Tillotson 228cc powered four wheel drive power wheels go kart, and take it for a spin! The gearing is still too tall, but it’s already performing much better. Ike takes the power wheels go kart off a jump, and soon after the front suspension falls apart because we hadn’t used proper locking nuts during assembly. We bolt the front suspension back together with the proper hardware, build floor pans, build a fuel tank and seat, and take it for another spin. We still need a gas and brake pedal, and a slightly shorter gear, but so far this little ford bronco go kart rips and the suspension feels great!
Thanks for Watching!
Facebook: goo.gl/VR6mh2
Instagram: goo.gl/PqOIo3
-----------------Go Power Sports Parts Used in Today’s Video----------------
Tell them CarsandCameras sent you at checkout:
Mechanical disc brake kit: bit.ly/3gx4URO
4” brake drum, 1” bore: bit.ly/38FrZyl
4” brake band: bit.ly/38FEgD5
Heavy duty cable: bit.ly/2ZzU5Fc
Fuel pump: bit.ly/3rC9ByU
Gussets: bit.ly/38VUN63
Go Power Sports: goo.gl/c2Tz6o
Get $100 off any Langmuir Systems Crossfire CNC plasma table using this link, or use code CARSANDCAMERAS at checkout: store.langmuirsystems.com/discount/CARSANDCAMERAS
NEW MERCH: www.cars-cameras.com/
Equipment we use: www.amazon.com/shop/carsandcameras
The following video features activities performed in controlled environments by knowledgeable persons. DO NOT attempt to duplicate, re-create, or perform the same or similar activities at home, as personal injury or property damage may result. CARS AND CAMERAS, the persons shown in this video and ANY CONTRIBUTOR, ARE NOT LIABLE FOR ANY such injury or damage. ALL CARSANDCAMERAS CONTENT IS FOR ENTERTAINMENT PURPOSES ONLY.

Cars and Cameras makes no representation about the sufficiency of any safety precautions and equipment used in this video.

Сэтгэгдлүүд
XtremeGMjunkieXL
XtremeGMjunkieXL 5 өдрийн өмнө
Ike kinda looks like arthur morgan from rdr2
JYD
JYD 27 өдрийн өмнө
Now you have to get yourself a knome to put in the garage... Er shop
Bryant Thornock
Bryant Thornock 29 өдрийн өмнө
Just a little tip for the next time you guys make a sealed container. If you drill an air/pilot hole before you seal of the last few areas with weld material you won't get as many leaks in those welds. If you don't do that, it essentially does what it did when Ike was trying to weld with it pressurized but not so drastic. This is just something that I learned when I was doing a pressure box in my welding class at school. Thanks for all of the great stuff you guys do! It has inspired me more that you might think.
Matt Willard
Matt Willard Сарын өмнө
Looking like Grind Hard Plumbing Company. mnpost.info/zone/fLzIeti7edx1pmE/video
Dax Carr
Dax Carr Сарын өмнө
You guys definitely need an anti-sway bar every time Isaac tries to jump it it’s leaning to the left have an excellent day
Grape Fox
Grape Fox Сарын өмнө
the fox running across infront of u is the foxos, saying this build will ZOOM and itll be awesome, and as im a fox, i also say it will zoom
Nathan Stribrny
Nathan Stribrny Сарын өмнө
You guys could really use a tig welder. Everlast is cheapish and works good.
alangri2000
alangri2000 Сарын өмнө
I'm watching this in Jan 21 so it's probably been addressed but I don't see a fill neck. Also was thinking a small jerry can gas tank would be cool on the back.
William Wille
William Wille Сарын өмнө
Did you make sure you cleaned out metal shavings from drilling it before you put in the bung for fuel line
fishing and camping with john
fishing and camping with john Сарын өмнө
typical ford broken down being towed lmao
saha6818
saha6818 Сарын өмнө
Ike is the pulse pump (when he bounces on the seat).
johnnybikesalot
johnnybikesalot Сарын өмнө
I would love to weld a squishy suspension like this onto my basically rigid manco dingo, that would be so cool.
Carl's Computer Hardware
Carl's Computer Hardware Сарын өмнө
hey i just found this it might help with your turning issues. here is the video. mnpost.info/zone/bb7PZ5nFbNKsnWk/video&ab_channel=What%27sgoingoninDoug%27sShed%3F
Jimmy C and Friends
Jimmy C and Friends Сарын өмнө
Now you guys need to build a Recovery Vehicle
TanTheMan
TanTheMan Сарын өмнө
What gear ratio are y'all are running? I've got a stage 1 Predator 420 on a little 2 seater running about 4.11 I believe and the drive pulley never pulls in, the clutch does perfect but the drive pulley stays all the way out the whole time. (Series 40 GPS)
Ervin Goertzen
Ervin Goertzen Сарын өмнө
You guys could use a hydraulic motorcycle lift
Donald Fuller
Donald Fuller Сарын өмнө
You guys need to challenge yourselves and do a build that's up to the builds coming out of the grind hards stable.
RotarE30 Guy
RotarE30 Guy Сарын өмнө
Yo what's the update with the pond? Did it ever clear up?
Shawn Waters
Shawn Waters Сарын өмнө
Is there another phone number for go powersports ... I wanna order a lot of stuff
Zark Muckerberg
Zark Muckerberg Сарын өмнө
Yes, 866-846-5278. I don't think they do phone orders though. They have a website(I doubt there is a limit to the cart) as well: www.gopowersports.com
Adam
Adam Сарын өмнө
would love if you were able to ship to 🇨🇦 🍁 🇨🇦 I would buy some merchandise.
Official. TrillWill
Official. TrillWill Сарын өмнө
Hello community I just need SUM HELP, I recently built a go kart predator 212 engine and it took me around a month to two months in between waiting for the parts and putting it together the upgrades that I made are governor removal,oil sensor removal, upgraded air filter, upgrade jet I check the oil fuel and the gas fuel and everything is perfect please help!!? I crank it up and it shakes like it wants to do something.....
Donald Tavares
Donald Tavares Сарын өмнө
Nice Seatank right there!
Alexander Lundgren
Alexander Lundgren Сарын өмнө
Get in touch with this guy and build a crazy electric gocart and run the CnC-GP!!! Austinwawa: mnpost.info/id/kURR2CLd5iDc0B11rSkFeg
Steven Haynes
Steven Haynes Сарын өмнө
How come you guys decide to slow everything down
Bill Lee
Bill Lee Сарын өмнө
My gosh! There is a lot of technology in this thing for a simple little go cart. It’s got NASA level gantry crane bracing, Indy 500 simulated sprockets, heavy construction chains and gearing. All without any cad cam drawings or even so much is a scribble on the back of a tavern napkin. Incredible job
Kyle Nichols
Kyle Nichols Сарын өмнө
I hope y'all see this! I need help/advice! I put together a cart for my daughter for Xmas, it is a 1993 manco 2 seater and it had a 5hp brigs, well that motor needed more than I wanted to do so, I had a 6.5 hp honda that I put on, got everything workingish... The problem I'm having is the belt is just a hair to tight and the cart basically doesn't have neutral. My question is how do I measure the belt, and who do you recommend I buy one from?!?!? I hope to hear from yall!
Logan Rowe
Logan Rowe Сарын өмнө
bring back the 440 Murry
DamLit Productions
DamLit Productions Сарын өмнө
"Isuck" It wont be fine,, I get "The learn as we go along" WORDS, but both you have lots of experience by now, and a mechanic, How are you still showing us "BODGE JOB DEATH TRAPS....We feel your pain come through on the videos....F Life Insurance, Write up a "WILL"...be fine...
Earl Dupont
Earl Dupont Сарын өмнө
Stretch the chassis a little....more room for Issac
Kenny Campbell Jr
Kenny Campbell Jr Сарын өмнө
When are you guys resurrecting the Cross Cart?
Dylan Bradley
Dylan Bradley Сарын өмнө
I’m loving the beard guys hahahaha
Dax Carr
Dax Carr Сарын өмнө
It would be absolutely hilarious of Taylor got a chance to drive that
Gv Chevy
Gv Chevy Сарын өмнө
Ive been watching you guys for 3 years now and i still cant figure out why you guys dont make your carrs bigger for issac when you guys build them. Make the carts bigger for you guys. I wouldnt want to ride something this small.
LindaStevensBZ
LindaStevensBZ Сарын өмнө
You could probably sell those little trucks
Mike Puckett
Mike Puckett Сарын өмнө
You guys might consider motorcycle handlebars and controls on this one
Michael Dover
Michael Dover Сарын өмнө
Looks uncomfortable sitting on it maybe some pegs or something just looks cramped cool look though
akkudakkupl
akkudakkupl Сарын өмнө
Hey guys maybe you could measure your built engines real power... It's super easy to build a simple chassis dyno with arduino and some hardware bits. If you want help with software side of things contact me ;-) Basicaly what you need to do is: Get a large diameter pipe - measure the diameter, weigh the pipe - this will be your dyno roller. Weld end caps on the pipe, add axis, self aligning bearings, etc. hardware. You need to calculate your roller moment of inertia (moment of inertia for a hoop around its symetry axis = roller mass times radius squared). Now you need a sensor that will pulse once per roller revolution - this can be an induction sensor that will sense a tooth welded to your roller axis. Your instrumentation device will measure time intervals between roller revolutions and send that data to your computer (arduino through serial link - real simple). From this data you will calculate your angular velocities and angular acceleration - Excel or OpenOffice will make this real easy and give you graphs ;-) Your torque at given angular velocity is your angular acceleration times roller moment of inertia. Your power at given angular velocity is angular velocity times torque.
fatbuddycat
fatbuddycat 2 сарын өмнө
HELP!! What causes derailment on the MB200-2 more, the 60t or the suspension lift? I'm trying to make a life altering decision here so any input would be GREATLY appreciated! I'm running a stage 2 plus a 14cc head with a CS grind cam and 22# springs for 7,000rpm. I'm already going to get a juggernaut but I need some guidance for the sprocket, you think a 54t with a juggernaut is a good idea since I'm jacking about 15hp?
Lucas Nolte
Lucas Nolte 2 сарын өмнө
It’s Primes the fuel lines when you sit down😂
J0rdanRaY 508
J0rdanRaY 508 2 сарын өмнө
Throw it out!! This is hard to watch
J0rdanRaY 508
J0rdanRaY 508 2 сарын өмнө
Been a long time sub. No offense but this thing sucks, too small, and need a giant kitten on the hood! 😹😹😻
Rob's small engine antics
Rob's small engine antics 2 сарын өмнө
I have an idea that I think would be a challenge, this is the only way I know of to get my idea to you. A mini bike with a super stretched frame, 420cc predator... and build it to look like the drag bikes that the rider almost lays down on his stomach. Or if you have a big 2 stroke motor with transmission that would have more potential.
Hockey Sockeys
Hockey Sockeys 2 сарын өмнө
Dose anyone know where I can get a yerfdog
danny stubblefield
danny stubblefield 2 сарын өмнө
Blue locktite is your friend.
Nathan Wadding
Nathan Wadding 2 сарын өмнө
You guys should instead of pedals use a brake handle off a pedal bike for the gas
Chanler Johnson
Chanler Johnson 2 сарын өмнө
You got any dirt bikes you would get rid of
tyler238
tyler238 2 сарын өмнө
Looks cramped
Quetzalcoatl Toltec Sun God
Quetzalcoatl Toltec Sun God 2 сарын өмнө
Any news on a new drag rail build I really want to see one with a twin 400cc 2 stroke engine.
jose Garcia
jose Garcia 2 сарын өмнө
Hey guys do you still offer a coupon code for go power sports ??
SportbikerNZ
SportbikerNZ 2 сарын өмнө
This was a great episode. It's shaping up awesome.
Tim Fetters
Tim Fetters 2 сарын өмнө
Here’s my advice to help you have a happy and prosperous new year: if you find leaks in the gas tank (which is awesome, btw) after you’ve put gas in it, don’t touch up the welds! LOL Pour a liner in it.
Harsh Fire
Harsh Fire 2 сарын өмнө
I would say to stiff just the rear a little bit
Mark Schaffer
Mark Schaffer 2 сарын өмнө
yall need a heater ,i can see yall breath lol
Larry Fogle
Larry Fogle 2 сарын өмнө
Extend the wheelbase 12” to 18” in the middle. Might as well make it rider friendly.
willowbrook hermit
willowbrook hermit 2 сарын өмнө
Look at the old Willis jeets you're setting on the gas tank
sleeperking01
sleeperking01 2 сарын өмнө
You guys should have made it atleast an inch 1/2 longer so its more comfortabe feet wise
willowbrook hermit
willowbrook hermit 2 сарын өмнө
What did you do with the electric motors Hook them up to a bicycle.
Wade Wright
Wade Wright 2 сарын өмнө
Y'all really need a sump for the fuel tank. It's so wide and shallow.
James McGee
James McGee 2 сарын өмнө
This kart is awesome guys. There are plenty of free gear ratio calculator apps out there. Forget all of the guess work and take advantage of those Phone apps.
akkudakkupl
akkudakkupl 2 сарын өмнө
Cool thing
Peter Emery
Peter Emery 2 сарын өмнө
Will the fuel filler be side or rear-mounted?
Built Minis
Built Minis 2 сарын өмнө
Are you surprised it broke lol
Nathan Louis
Nathan Louis 2 сарын өмнө
I think you need more commercials
WrenchandRip
WrenchandRip 2 сарын өмнө
even though its way too soft it is cool to watch all your suspension work in action
TandM bros
TandM bros 2 сарын өмнө
I think it needs handle bars instead of a steering wheel
Bo Boura
Bo Boura 2 сарын өмнө
Nice build. But whatever happened to that diesel engine and why hasn't it been put in the monster truck ? Its already a torque monster why not go ballz to the walls with the torque . Burnouts that pulls the earth out of rotation
Micah LeVoy
Micah LeVoy 2 сарын өмнө
What happened to the video you posted today? Did it get taken down?
Jay Titus
Jay Titus 2 сарын өмнө
Where is your holiday burnout? See VGG to see what I mean. Gitter done!
John Brown
John Brown 2 сарын өмнө
Beef up the rear suspension a bit and you got it....
Lyle Williams
Lyle Williams 2 сарын өмнө
u guys should make a go kart that looks and performs just like the go kart on gta 5
Ihave Noclue
Ihave Noclue 2 сарын өмнө
Ike in his size 12. I'm crying in size 14 😭😭🤣🤣🤣🤣
g meeks
g meeks 2 сарын өмнө
Ok guys I have a idea for you . Try to use 21 speed bicycle gearing on a project,it would be like a big rig with a high low axle :)
Jon g
Jon g 2 сарын өмнө
Need heavier shocks like atv shocks not go kart shocks at least for the rear
Mark Rogers
Mark Rogers 2 сарын өмнө
That looks great guys!
Cameron Wilson
Cameron Wilson 2 сарын өмнө
Hook the gas pedal up to the steering wheel it would work good for crawling
Matthew Soltis
Matthew Soltis 2 сарын өмнө
Hey can i get youre email just watched the live
Zark Muckerberg
Zark Muckerberg Сарын өмнө
Jinzerillo64@gmail.com At least that's the email from their about page.
XtReMe DiY
XtReMe DiY 2 сарын өмнө
​I am building a tecumseh ah600 any carb suggestions? 98cc 2 stroke.
Charles Levac
Charles Levac 2 сарын өмнө
Hi Guys for the gearing. Why did you guys decide to go to a bigger sprocket in stead of going to a smaller front sprocket. You needed a big change and going down 1 or 2 teeth would be a bigger change in gearing then going up a bunch of teeth on the rear. Just wondering..
Logan Aldridge
Logan Aldridge 2 сарын өмнө
Where is the Murrayt kilowatts with the arctic cat motor it has been sitting for three years
Edward Wynn
Edward Wynn 2 сарын өмнө
Chances of getting a 2020 in review video?
isac scot
isac scot 2 сарын өмнө
big clap on trying tho
isac scot
isac scot 2 сарын өмнө
dont do any more on dat
Nick W
Nick W 2 сарын өмнө
You guys should really do some research on shock angles and pivot points, you could literally screen shot MNpost videos of off road cars, sand cars and the like and measure the angles to make things work better looking at the angle of those rear shocks vs the articulation of the rear end seems like the shocks really aren’t dampening anything, just side loading the shock shafts.. , just a suggestion. I like the videos regardless just thinking you guys are holding your skills back a little, I think you guys have the ability to do wayyy more if you just look up the angles
Caleb Todd
Caleb Todd 2 сарын өмнө
Should do a give away on one of those carts. By selling merch
Legoman585
Legoman585 2 сарын өмнө
The power wheels looked awesome coming around the corner before the jump.
How to Paint with Brettski
How to Paint with Brettski 2 сарын өмнө
Back of seat you have bar going straight across, maybe Ikes butt will have more room if you curved that rear bar?..
Eli Renigar
Eli Renigar 2 сарын өмнө
I’d extended the wheelbase dead in the center just a tad for posterity
Michael Mezey
Michael Mezey 2 сарын өмнө
Great build just think you guys should have made the frame longer it would handle alot better
Trevor Miller
Trevor Miller 2 сарын өмнө
Happy New year! 🥳
michael Thomas
michael Thomas 2 сарын өмнө
I hope it works out for you guys but I don't think it's a very good idea using a bigger disc and that other brake caliper I think that they're supposed to be a match set because of a bigger circles going to make a difference in your caliper grab of the disc which is why even cars when you upgrade the discs you have to upgrade the calipers because they're bigger calipers for bigger rotors
Chicken Fingers
Chicken Fingers 2 сарын өмнө
For the fuel tank you can just weld it up, seal the out side with jbweld and coat the inside with tank liner
Luke Benton
Luke Benton 2 сарын өмнө
Y’all should make a qna and one of the questions should be what y’all do for a living
Joel Ducsai
Joel Ducsai 2 сарын өмнө
Can you guys start using good suspension even use stuff from the front end of past 20 years of 4 wheelers rather than........ the lower quality shocks you use??
Tom Kimbrel
Tom Kimbrel 2 сарын өмнө
Am I missing something; maybe a fuel filler neck and a gas cap? Somehow a way to fill the tank and a vent?
samiam20024
samiam20024 2 сарын өмнө
Turbocharged briggs and stratton engine
skullboi2012Plays
skullboi2012Plays 2 сарын өмнө
This thing is sweet but you might want to stretch it just a little bit more
three wheela
three wheela 2 сарын өмнө
Sitting on the gas tank? Yeah no thanks.
Review Account
Review Account 2 сарын өмнө
Needs some back support, at least a simple hoop with a pad on it.
apaudorff
apaudorff 2 сарын өмнө
Stretch it some, seems way to short of a wheelbase to actually be able to floor it
Forgotten Polaris ATV | Will it Run after Sitting in a Barn for 22 Years?
48:03
Авдрын ёроол - Intro (EPISODE 1)
17:05
THUNDERZ
Үзсэн тоо 88мянга.
Watch NASA’s Perseverance Rover Land on Mars!
2:11:44
4x4 Bronco Power Wheels Go Kart First Rip! | Mud Run, Jumps, & More!
24:36
CarsandCameras
Үзсэн тоо 156мянга.
I CRASHED OUR 1000cc Trophy Truck on the FIRST HOT LAP!
23:39
CarsandCameras
Үзсэн тоо 220мянга.
1000cc Trophy Truck TRANSFORMATION | Lift + Splatter Paint!
28:08
CarsandCameras
Үзсэн тоо 189мянга.
670cc Drag Rail Revival! | Our 55HP Harbor Freight Engine Rail Kart Returns!
19:15
Crusher Mini Bike Build | $20 Mini Bike Gets a Tillotson 225!
20:42
CarsandCameras
Үзсэн тоо 181мянга.
How to Diesel Swap a Vanagon - 4x4 Camper Van Build 2.0L TDI
44:38
Grind Hard Plumbing Co
Үзсэн тоо 771мянга.
The 100HP Power Wheels Jeep is Finished! Painting and Final Look!
18:47
Grind Hard Plumbing Co
Үзсэн тоо 1,7сая
Go Kart Mysteriously Appears at our Shop... Can We Make it Run and Ride?
33:37
Unboxing and installing ALL the mad parts on our twin charged Nissan
32:37
Mighty Car Mods
Үзсэн тоо 629мянга.
Авдрын ёроол - Intro (EPISODE 1)
17:05
THUNDERZ
Үзсэн тоо 88мянга.
Watch NASA’s Perseverance Rover Land on Mars!
2:11:44